This website stores cookies on your computer. These cookies are used to collect information about how you interact with our website and allow us to remember your browser. We use this information to improve and customize your browsing experience, for analytics and metrics about our visitors both on this website and other media, and for marketing purposes. By using this website, you accept and agree to be bound by UVic’s Terms of Use for web and social media privacy.  If you do not agree to the above, you can configure your browser’s setting to “do not track.”

Skip to main content

Abdullah Tayyem

  • BEng (Al-Balqa Applied University, 2017)

Notice of the Final Oral Examination for the Degree of Master of Applied Science

Topic

Modeling the Impact of Porous Transport Layer Defects and Microporous Layer Morphology on Transport and Interfacial Contact in Proton Exchange Membrane Water Electrolyzers

Department of Mechanical Engineering

Date & location

  • Tuesday, December 1, 2026

  • 10:00 A.M.

  • Engineering Office Wing

  • Room 230

Reviewers

Supervisory Committee

  • Dr. Jason Keonhag Lee, Department of Mechanical Engineering, University of Victoria (Supervisor)

  • Dr. Samira Gharehkhani, Department of Mechanical Engineering, UVic (Member) 

External Examiner

  • Dr. Ardeshir Shojaeinasab, Department of Electrical and Computer Engineering, UVic 

Chair of Oral Examination

  • Dr. Michael McGuire, Department of Electrical and Computer Engineering, UVic 

Abstract

Reducing the cost of green hydrogen is essential to enable the widespread adoption of hydrogen technologies. While the proton exchange membrane (PEM) water electrolyzer is one of the promising technologies viable for mass production, the capital expenditure of the system must be reduced. Specifically, porous transport layers (PTLs) and microporous layers (MPLs) play a vital role in cost reduction. 

This thesis reveals how key morphological defects in the PTL can critically affect transport and interfacial contact with the catalyst layer (CL). Stochastic and pore network modeling are used to create and evaluate defects, including thickness variations, positive protrusions, pinholes, porosity variations, cracks, and negative protrusions. The results show that thickness variations and positive protrusions severely affect electrolysis by increasing PTL roughness and tortuosity. A 60% thickness variation produced the greatest increase in tortuosity, nearly doubling it, whereas a 100 μm positive protrusion had the greatest impact on roughness, increasing it by approximately tenfold. Furthermore, they reduced water's effective permeability by flooding the oxygen gas, preventing reactant water from reaching reaction sites. In contrast, cracks, negative protrusions, and pinholes have a minor impact on electrolysis. In fact, they enhance the absolute and effective water permeability. This thesis proposes reorienting defect PTLs during cell assembly to mitigate their negative effects while retaining transport benefits, thereby reducing capital costs by reusing them rather than replacing them. 

MPLs have been fabricated in the literature as backing layers with smaller pores than conventional PTLs, thereby improving mass transport by enhancing interfacial contact and reducing gas clustering. We selected fiber-based structures because of their wide market availability. However, the complexity of the fabrication process, which requires high temperatures and chemical affinity for atmospheric gas limits MPL design options and poses significant challenges for experimental optimization. We developed four novel fiber-based MPL types: simple fiber, powder-loaded fiber, electrospun fiber, and electrospun fiber with pore formers. Because PEM electrolyzers are costly due to the high catalyst loading required to enhance in-plane CL conductivity, we developed electrospun nanofiber MPLs to maximize interfacial contact and minimize CL loading. Electrospun MPLs exhibited permeabilities approximately two orders of magnitude lower than other studied MPL types, but they provide superior interfacial contact, leading to an 8.5 fold reduction in CL in-plane resistance and voltage loss at a 0.1 mgIr·cm-2 loading compared to the conventional 40% simple fiber MPL with a 2 μm radius. Results indicate that careful consideration of MPL and PTL structure is essential to improve PEM electrolyzer performance and enable gigawatt scale deployment.